AT32UC3B1512-Z1UT

The AT32UC3B is a complete System-On-Chip microcontroller based on the AVR32 UC RISC processor running at frequencies up to 60 MHz. AVR32 UC is a high-performance 32-bit RISC microprocessor core, designed for cost-sensitive embedded applications, with particular emphasis on low power consumption, high code density and high performance. The processor implements a Memory Protection Unit (MPU) and a fast and flexible interrupt controller for supporting modern operating systems and real-time operating systems. The AT32UC3B incorporates on-chip Flash and SRAM memories for secure and fast access. The Peripheral Direct Memory Access controller enables data transfers between peripherals and memories without processor involvement. PDCA drastically reduces processing overhead when transferring continuous and large data streams between modules within the MCU. The Power Manager improves design flexibility and security: the on-chip Brown-Out Detector monitors the power supply, the CPU runs from the on-chip RC oscillator or from one of external oscillator sources, a Real-Time Clock and its associated timer keeps track of the time. The Timer/Counter includes three identical 16-bit timer/counter channels. Each channel can be independently programmed to perform frequency measurement, event counting, interval measurement, pulse generation, delay timing and pulse width modulation. The PWM modules provides seven independent channels with many configuration options including polarity, edge alignment and waveform non overlap control. One PWM channel can trigger ADC conversions for more accurate close loop control implementations. The AT32UC3B also features many communication interfaces for communication intensive applications. In addition to standard serial interfaces like USART, SPI or TWI, other interfaces like flexible Synchronous Serial Controller and USB are available. The USART supports different communication modes, like SPI mode. The Synchronous Serial Controller provides easy access to serial communication protocols and audio standards like I²S, UART or SPI. The Full-Speed USB 2.0 Device interface supports several USB Classes at the same time thanks to the rich End-Point configuration. The Embedded Host interface allows device like a USB Flash disk or a USB printer to be directly connected to the processor. Atmel offers the QTouch library for embedding capacitive touch buttons, sliders, and wheels functionality into AVR microcontrollers. The patented charge-transfer signal acquisition offers robust sensing and included fully debounced reporting of touch keys and includes Adjacent Key Suppression® (AKS™) technology for unambiguous detection of key events. The easy-to-use QTouch Suite toolchain allows you to explore, develop, and debug your own touch applications. AT32UC3B integrates a class 2+ Nexus 2.0 On-Chip Debug (OCD) System, with non-intrusive real-time trace, full-speed read/write memory access in addition to basic r

Key features

• High Performance, Low Power 32-Bit Atmel AVR Microcontroller
• Compact Single-cycle RISC Instruction Set Including DSP Instruction Set
• Read-Modify-Write Instructions and Atomic Bit Manipulation
• Performing up to 1.39 DMIPS / MHz
• Up to 83 DMIPS Running at 60 MHz from Flash
• Up to 46 DMIPS Running at 30 MHz from Flash
• Memory Protection Unit
• Multi-hierarchy Bus System
• High-Performance Data Transfers on Separate Buses for Increased Performance
• 7 Peripheral DMA Channels Improves Speed for Peripheral Communication
• Internal High-Speed Flash
• 512K Bytes, 256K Bytes, 128K Bytes, 64K Bytes Versions
• Single Cycle Access up to 30 MHz
• Prefetch Buffer Optimizing Instruction Execution at Maximum Speed
• 4ms Page Programming Time and 8ms Full-Chip Erase Time
• 100,000 Write Cycles, 15-year Data Retention Capability
• Flash Security Locks and User Defined Configuration Area
• Internal High-Speed SRAM, Single-Cycle Access at Full Speed
• 96K Bytes (512KB Flash), 32K Bytes (256KB and 128KB Flash), 16K Bytes (64KB Flash)
• Interrupt Controller
• Autovectored Low Latency Interrupt Service with Programmable Priority
• System Functions
• Power and Clock Manager Including Internal RC Clock and One 32KHz Oscillator
• Two Multipurpose Oscillators and Two Phase-Lock-Loop (PLL) allowing Independant CPU Frequency from USB Frequency
• Watchdog Timer, Real-Time Clock Timer
• Universal Serial Bus (USB)
• Device 2.0 and Embedded Host Low Speed and Full Speed
• Flexible End-Point Configuration and Management with Dedicated DMA Channels
• On-chip Transceivers Including Pull-Ups
• USB Wake Up from Sleep Functionality
• One Three-Channel 16-bit Timer/Counter (TC)
• Three External Clock Inputs, PWM, Capture and Various Counting Capabilities
• One 7-Channel 20-bit Pulse Width Modulation Controller (PWM)
• Three Universal Synchronous/Asynchronous Receiver/Transmitters (USART)
• Independant Baudrate Generator, Support for SPI, IrDA and ISO7816 interfaces
• Support for Hardware Handshaking, RS485 Interfaces and Modem Line
• One Master/Slave Serial Peripheral Interfaces (SPI) with Chip Select Signals
• One Synchronous Serial Protocol Controller
• Supports I²S and Generic Frame-Based Protocols
• One Master/Slave Two-Wire Interface (TWI), 400kbit/s I2C-compatible
• One 8-channel 10-bit Analog-To-Digital Converter, 384ks/s
• 16-bit Stereo Audio Bitstream DAC
• Sample Rate Up to 50 kHz
• QTouch Library Support
• Capacitive Touch Buttons, Sliders, and Wheels
• QTouch and QMatrix Acquisition
• On-Chip Debug System (JTAG interface)
• Nexus Class 2+, Runtime Control, Non-Intrusive Data and Program Trace
• 5V Input Tolerant I/Os, including 4 high-drive pins
• Single 3.3V Power Supply or Dual 1.8V-3.3V Power Supply