AT90USB647-AU

The Atmel AVR AT90USB64/128 is a low-power CMOS 8-bit microcontroller based on the Atmel AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the AT90USB64/128 achieves throughputs approaching 1MIPS per MHz allowing the system designer to optimize power consumption versus processing speed.

Key features

• High performance, low power 8-bit Microcontroller
• Advanced RISC architecture
• 135 powerful instructions
• most single clock cycle execution
• 32×8 general purpose working registers
• Fully static operation
• Up to 16MIPS throughput at 16MHz
• On-chip 2-cycle multiplier
• Non-volatile program and data memories
• 64/128Kbytes of in-system self-programmable flash
• Endurance: 100,000 write/erase cycles
• Optional Boot Code section with independent lock bits
• USB boot loader programmed by default in the factory
• In-system programming by on-chip boot program hardware activated after reset
• True read-while-write operation
• All supplied parts are pre-programed with a default USB bootloader
• 2K/4K (64K/128K flash version) bytes EEPROM
• Endurance: 100,000 write/erase cycles
• 4K/8K (64K/128K flash version) bytes internal SRAM
• Up to 64Kbytes optional external memory space
• Programming lock for software security
• JTAG (IEEE std. 1149.1 compliant) interface
• Boundary-scan capabilities according to the JTAG standard
• Extensive on-chip debug support
• Programming of flash, EEPROM, fuses, and lock bits through the JTAG interface
• USB 2.0 full-speed/low-speed device and on-the-go module
• Complies fully with:
• Universal serial bus specification REV 2.0
• On-the-go supplement to the USB 2.0 specification rev 1.0
• Supports data transfer rates up to 12Mbit/s and 1.5Mbit/s
• USB full-speed/low speed device module with interrupt on transfer completion
• Endpoint 0 for control transfers: up to 64-bytes
• Six programmable endpoints with in or out directions and with bulk, interrupt or isochronous transfers
• Configurable endpoints size up to 256bytes in double bank mode
• Fully independent 832bytes USB DPRAM for endpoint memory allocation
• Suspend/resume interrupts
• Power-on reset and USB bus reset
• 48MHz PLL for full-speed bus operation
• USB bus disconnection on microcontroller request
• USB OTG reduced host
• Supports host negotiation protocol (HNP) and session request protocol (SRP) for OTG dual-role devices
• Provide status and control signals for software implementation of HNP and SRP
• Provides programmable times required for HNP and SRP
• Peripheral features
• Two 8-bit timer/counters with separate prescaler and compare mode
• Two 16-bit timer/counter with separate prescaler, compare- and capture mode
• Real time counter with separate oscillator
• Four 8-bit PWM channels
• Six PWM channels with programmable resolution from 2 to 16 bits
• Output compare modulator
• 8-channels, 10-bit ADC
• Programmable serial USART
• Master/slave SPI serial interface
• Byte oriented 2-wire serial interface
• Programmable watchdog timer with separate on-chip oscillator
• On-chip analog comparator
• Interrupt and wake-up on pin change
• Special microcontroller features
• Power-on reset and programmable brown-out detection
• Internal calibrated oscillator
• External and internal interrupt sources
• Six sleep modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby, and Extended Standby
• I/O and packages
• 48 programmable I/O lines
• 64-lead TQFP and 64-lead QFN
• Operating voltages: 2.7 - 5.5V
• Operating temperature: Industrial (-40℃ to +85℃)
• Maximum frequency
• 8MHz at 2.7V - industrial range
• 16MHz at 4.5V - industrial range