LPC43S57JET256E

The LPC43S5x/S3x are ARM Cortex-M4 based microcontrollers for embedded applications which include an ARM Cortex-M0 coprocessor, up to 1 MB of flash and 136 kB of on-chip SRAM, 16 kB of EEPROM memory, security features with AES engine, a quad SPI Flash Interface (SPIFI), advanced configurable peripherals such as the State Configurable Timer (SCT) and the Serial General Purpose I/O (SGPIO) interface, two High-speed USB controllers, Ethernet, LCD, an external memory controller, and multiple digital and analog peripherals. The LPC43S5x/S3x operate at CPU frequencies of up to 204 MHz. The ARM Cortex-M4 is a 32-bit core that offers system enhancements such as low power consumption, enhanced debug features, and a high level of support block integration. The ARM Cortex-M4 CPU incorporates a 3-stage pipeline, uses a Harvard architecture with separate local instruction and data buses as well as a third bus for peripherals, and includes an internal prefetch unit that supports speculative branching. The ARM Cortex-M4 supports single-cycle digital signal processing and SIMD instructions. A hardware floating-point unit is integrated in the core. The ARM Cortex-M4 with floating-point unit is often referred to as M4F. The ARM Cortex-M0 coprocessor is an energy-efficient and easy-to-use 32-bit core which is upward code- and tool-compatible with the Cortex-M4 core. The Cortex-M0 coprocessor, designed as a replacement for existing 8/16-bit microcontrollers, offers up to 204 MHz performance with a simple instruction set and reduced code size.

Applications

• Various embedded applications
• Drop-in replacement for existing 8/16-bit microcontroller applications

Key features

• Cortex-M4 Processor core
• ARM Cortex-M4 processor (version r0p1), running at frequencies of up to 204 MHz.
• Built-in Memory Protection Unit (MPU) supporting eight regions.
• Built-in Nested Vectored Interrupt Controller (NVIC).
• Hardware floating-point unit.
• Non-maskable Interrupt (NMI) input.
• JTAG and Serial Wire Debug (SWD), serial trace, eight breakpoints, and four watch points.
• Enhanced Trace Module (ETM) and Enhanced Trace Buffer (ETB) support.
• System tick timer.
• Cortex-M0 Processor core
• ARM Cortex-M0 coprocessor (version r0p0) capable of off-loading the main ARM Cortex-M4 application processor.
• Running at frequencies of up to 204 MHz.
• JTAG
• Built-in NVIC.
• On-chip memory
• Up to 1 MB on-chip dual bank flash memory with flash accelerator.
• 16 kB on-chip EEPROM data memory.
• 136 kB SRAM for code and data use.
• Multiple SRAM blocks with separate bus access. Two SRAM blocks can be powered down individually.
• 64 kB ROM containing boot code and on-chip software drivers.
• 64 bit of One-Time Programmable (OTP) memory for general-purpose use.
• Two banks (256 bit total) One-Time Programmable (OTP) memory for AES key storage. One bank can store an encrypted key for decoding the boot image.
• AES engine for encryption and decryption of the boot image and data with DMA support and programmable via a ROM-based API.
• Configurable digital peripherals
• Serial GPIO (SGPIO) interface.
• State Configurable Timer (SCT) subsystem on AHB.
• Global Input Multiplexer Array (GIMA) allows to cross-connect multiple inputs and outputs to event driven peripherals like the timers, SCT, and ADC0/1.
• Serial interfaces
• Quad SPI Flash Interface (SPIFI) with four lanes and up to 52 MB per second.
• 10/100T Ethernet MAC with RMII and MII interfaces and DMA support for high throughput at low CPU load. Support for IEEE 1588 time stamping/advanced time stamping (IEEE 1588-2008 v2).
• One High-speed USB 2.0 Host/Device/OTG interface with DMA support and on-chip high-speed PHY.
• One High-speed USB 2.0 Host/Device interface with DMA support, on-chip full-speed PHY and ULPI interface to external high-speed PHY.
• USB interface electrical test software included in ROM USB stack.
• One 550 UART with DMA support and full modem interface.
• Three 550 USARTs with DMA and synchronous mode support and a smart card interface conforming to ISO7816 specification. One USART with IrDA interface.
• Up to two C_CAN 2.0B controllers with one channel each.
• Two SSP controllers with FIFO and multi-protocol support. Both SSPs with DMA support.
• One SPI controller.
• One Fast-mode Plus I2C-bus interface with monitor mode and with open-drain I/O pins conforming to the full I2C-bus specification. Supports data rates of up to 1 Mbit/s.
• One standard I2C-bus interface with monitor mode and with standard I/O pins.
• Two I2S interfaces, each with DMA support and with one input and one output.
• Digital peripherals
• External Memory Controller (EMC) supporting external SRAM, ROM, NOR flash, and SDRAM devices.
• LCD controller with DMA support and a programmable display resolution of up to 1024 H×768 V. Supports monochrome and color STN panels and TFT color panels; supports 1/2/4/8 bpp Color Look-Up Table (CLUT) and 16/24-bit direct pixel mapping. Available on parts LPC4357/53 only.
• Secure Digital Input Output (SD/MMC) card interface.
• Eight-channel General-Purpose DMA controller can access all memories on the AHB and all DMA-capable AHB slaves.
• Up to 164 General-Purpose Input/Output (GPIO) pins with configurable pull-up/pull-down resistors.
• GPIO registers are located on the AHB.