R5F524TEADFP#11

80-MHz 32-bit RX MCUs, on-chip FPU, 153.6 DMIPS, power supply 5 V, 12-bit ADC (equipped with 3-channel synchronous S/H circuits, double data registers, operating amplifiers, comparator) 3 units, Simultaneous sampling up to ADC 5 channels, CAN, 80-MHz PWM (three-phase complementary output × 2 channels + single-phase complementary output × 4 channels or three-phase complementary × 3 channels + single-phase complementary × 1 channel)

Applications

• General industrial and consumer equipment

Key features

• 32-bit RXv2 CPU core
• Max. operating frequency: 80 MHz Capable of 153.6 DMIPS in operation at 80 MHz
• Enhanced DSP: 32-bit multiply-accumulate and 16-bit multiply-subtract instructions supported
• Built-in FPU: 32-bit single-precision floating point (compliant to IEEE754)
• Divider (fastest instruction execution takes two CPU clock cycles)
• Fast interrupt
• CISC Harvard architecture with 5-stage pipeline
• Variable-length instructions, ultra-compact code
• On-chip debugging circuit
• Memory protection unit (MPU) supported
• Low power design and architecture
• Operation from a single 2.7-V to 5.5-V supply
• Three low power consumption modes
• On-chip code flash memory
• 512-/384-/256-/128-Kbyte capacities
• On-board or off-board user programming
• For instructions and operands
• On-chip data flash memory
• 8-Kbyte (Number of erase/write cycles: 1,000,000 (typ))
• BGO (Back Ground Operation)
• On-chip SRAM, no wait states
• 32-/16-Kbytes of SRAM
• Reset and supply management
• Seven types of reset, including the power-on reset (POR)
• Low voltage detection (LVD) with voltage settings
• Clock functions
• Main clock oscillator frequency: 1 to 20 MHz
• External clock input frequency: Up to 20 MHz
• PLL circuit input: 4 MHz to 12.5 MHz
• On-chip low-speed oscillators, On-chip high-speed oscillators, dedicated on-chip oscillator for the IWDT
• Clock frequency accuracy measurement circuit (CAC)
• Independent watchdog timer
• 15-kHz on-chip oscillator produces a dedicated clock signal to drive IWDT operation.
• Useful functions for IEC60730 compliance
• Self-diagnostic and disconnection-detection assistance functions for the A/D converter, clock frequency accuracy measurement circuit, independent watchdog timer, RAM test assistance functions using the DOC, etc.
• MPC
• Multiple locations are selectable for I/O pins of peripheral functions
• Up to 6 communications channels
• CAN (compliant with ISO11898-1), incorporating 16 message boxes (1 channel)
• SCI with many useful functions (3 channels) Asynchronous mode, clock synchronous mode, smart card interface mode, simplified SPI, simplified I²C, and extended serial mode.
• I²C bus interface: Transfer at up to 400 kbps, capable of SMBus operation (1 channel)
• RSPI capable of high speed connection Transfer at up to 20 Mbps (1 channel)
• Up to 25 extended-function timers
• 16-bit MTU3: 80 MHz operation, input capture, output compare, three-phase complementary PWM × 2 channels output, CPU-efficient complementary PWM, phase counting mode (nine channels)
• 16-bit GPT: 80 MHz operation, input capture, output compare, PWM wave-form single-phase complementary × 4 channels output or three-phase × 1 channel + singlephase complementary × 1 channel output, comparator interlocking operation (count operation, PWM negate control) (4 channels)
• 8-bit TMRs (8 channels)
• 16-bit compare-match timers (4 channels)
• 12-bit A/D converter: 22 channels in 3 units
• Incorporating sample-and-hold circuit 12 bits × 3 units (unit 0: 5 channels, unit 1: 5 channels, unit 2: 12 channels)
• Sampling time can be set for each channel
• Group scan priority control mode (3 levels)
• Self-diagnostic function and analog input disconnection detection assistance function (compliant to IEC60730)
• Input signal amplitude by the programmable gain amplifier (4 channels)
• ADC: 3-channel simultaneous sample-and-hold circuit (3 shunt method), double data register (1 shunt method), amplifier (4 channels), comparator (4 channels)
• 8-bit D/A converter: 2 channels
• This can be used as reference voltage for a comparator
• Register write protection function can protect values in important registers against overwriting.
• 5-V tolerant, open drain, input pull-up, switching of driving capacity
• Operating temperature range
• -40 to +85℃